Go Back   Two Wheel Fix > General > Cage Hell > Cage Tech

Reply
 
Thread Tools Display Modes
Old 05-20-2010, 04:53 PM   #71
101lifts2
WSB Champion
 
101lifts2's Avatar
 
Join Date: Nov 2008
Location: Anaheim, CA
Moto: 2009 Kawi ZX6R
Posts: 5,570
Default

Quote:
Originally Posted by azoomm View Post
Sorry, I missed this - I was referring to the Oil Filter Stand, one of the guys referred to it [to my husband] as a plunger.. that stuck.

Turns out, the motor ate itself. At least two injectors took out three cylinders. End result was putting in a new motor. That was the easiest repair So, now here I am with a 2004 truck with a 2006 motor that has 16,500 miles on it. It runs like a raped ape. My plan is to keep this thing until it tries to do that again - hopefully in about 200,000 miles...
Working for a truck manufacturer....were the injectors replaced, then you needed an engine? Sometimes the techs will not tighten the injector lines down and the engine oil gets full of fuel...then runs away. OR the Charge Air Cooler becomes full of oil and melts pistons.

I wouldn't buy a diesel on a light duty truck unless you really need it or have a good warranty. How much was the engine?
__________________
Train Hard

Ron Paul - 2012

Mark of Excellence
GM
101lifts2 is offline   Reply With Quote
Old 05-20-2010, 05:01 PM   #72
Homeslice
Elitist
 
Homeslice's Avatar
 
Join Date: Nov 2008
Location: SF Bay Area
Moto: Gix 750
Posts: 11,351
Default

what up with the black wheels? those aftermarket, or just the base steelies?
Homeslice is offline   Reply With Quote
Old 05-20-2010, 05:18 PM   #73
anthonyk
WERA White Plate
 
anthonyk's Avatar
 
Join Date: Nov 2008
Location: Austin, TX
Moto: '01 Aprilia Falco
Posts: 1,041
Default

see post #37
anthonyk is offline   Reply With Quote
Old 05-20-2010, 09:44 PM   #74
azoomm
moderator chick

 
azoomm's Avatar
 
Join Date: Feb 2008
Location: Hill Country TX
Moto: Pasta Rockets
Posts: 8,917
Default

Quote:
Originally Posted by 101lifts2 View Post
Working for a truck manufacturer....were the injectors replaced, then you needed an engine? Sometimes the techs will not tighten the injector lines down and the engine oil gets full of fuel...then runs away. OR the Charge Air Cooler becomes full of oil and melts pistons.

I wouldn't buy a diesel on a light duty truck unless you really need it or have a good warranty. How much was the engine?
Engine, install, delete and program for $5K

wheels are after market, God bless tire rack.
__________________
We have enough youth. How about a fountain of "smart"?

Come Play at the Track!!

http://www.elitetrackdays.com
azoomm is offline   Reply With Quote
Old 05-20-2010, 10:37 PM   #75
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

Quote:
Originally Posted by 101lifts2 View Post
And how does it not set a P0401 code?
Tuners. Electronics FTW!

Quote:
Originally Posted by azoomm View Post
Engine, install, delete and program for $5K

wheels are after market, God bless tire rack.
So the EGR is deleted on the engine going in? Good! Hope it works for you!

I'm still looking for mine...
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-29-2010, 02:20 AM   #76
101lifts2
WSB Champion
 
101lifts2's Avatar
 
Join Date: Nov 2008
Location: Anaheim, CA
Moto: 2009 Kawi ZX6R
Posts: 5,570
Default

Quote:
Originally Posted by Cutty72 View Post
Tuners. Electronics FTW!



So the EGR is deleted on the engine going in? Good! Hope it works for you!

I'm still looking for mine...
You would fail the Smog test here in CA (they check diesels now). If you left in the "tuner" controller you would fail the CVN (Calibration Verification Number) and if you installed the original controller, the On-board diagnostic systems would not have run and determined a Pass/Fail unless you ran the vehicle for a few days. They also check for add on components here.

The newer diesels (common rail injection) are required for OBD2 trucks to install the INJ flow rates in another on-board controller. If these do not match, you end up setting a Injector Flow Rate Calibration Error code and the Check Engine Light will be illuminated. The controller Isuzu uses is the Glow Plug Controller, so this is one step that makes the "tuner" crowd have to buy another controller. On top of it, the ECU checks the checksum of the flow rates each ignition cycle.

CARB is getting a little smarter, but I can tell them how to make it error proof so people wouldn't defeat emission control devices.
__________________
Train Hard

Ron Paul - 2012

Mark of Excellence
GM

Last edited by 101lifts2; 05-29-2010 at 02:23 AM..
101lifts2 is offline   Reply With Quote
Old 05-29-2010, 02:59 AM   #77
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

I'm not saying they would pass smog testing, but you can drive 'em just fine without codes.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:19 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.