96 S10 fuel issue

BobTheBiker · 08-28-2009, 10:36 PM

Anyone have some ideas here?

I've got a 96 S10 2.2, everyting is wired up right, and hooked up where its supposed to be, but I cant get the truck to run because the fuel injectors arent firing as they need to be. I've got ONE plug I cant figure out, looks just like the cam position sensor plug, but the notch is different and theres nowhere for it to go on my motor.

Right now, the truck runs with ether in the intake, but wont start on its own. I'm not really sure WTF to make of it, but its annoying as shit.

anyone got some input? My only idea now is ECU is toast.

101lifts2 · 08-29-2009, 02:52 AM

Quote:

Originally Posted by BobTheBiker

Anyone have some ideas here?

I've got a 96 S10 2.2, everyting is wired up right, and hooked up where its supposed to be, but I cant get the truck to run because the fuel injectors arent firing as they need to be. I've got ONE plug I cant figure out, looks just like the cam position sensor plug, but the notch is different and theres nowhere for it to go on my motor.

Right now, the truck runs with ether in the intake, but wont start on its own. I'm not really sure WTF to make of it, but its annoying as shit.

anyone got some input? My only idea now is ECU is toast.

If the vehicle runs off of ether, then the CAM and CRANK signals are ok or at least enough to run the engine.

Does the fuel pump energize with the key initially turned ON?

Check the ECM IGN 20A fuse that supplies ignition voltages to all 4 fuel injectors. Then make sure there is 12V at each fuel injector with the key on, engine off.

If you can get ahold of a noid light, you can plug it into one of the fuel injector connectors and crank over the engine. If the noid light blinks, you probably have a fuel delivery/regulator/fuel issue.

The ECM BATT 20A fuse feeds the fuel pump relay, but the the fuel pump will run w/o the relay if oil pressure is present (bypass).

BobTheBiker · 08-29-2009, 02:59 AM

I was looking at it more earlier and the issue dawned on me. I had the wrong fucking crank sensor in there. people keep saying how the crank sensor is behind the motor mount, but never mention a wire going to the coil off it, so I had to go swap with the one off my original block, along with the original coils.
BAM! problem seems to no longer be a problem, and all but 3 plugs(former AC system and one evap unit) now have homes. I'll test better in the AM since I'm in an apartment complex and theres little kids livin next to where I work on my truck. dont need angry neighbors.

101lifts2 · 08-29-2009, 09:43 PM

How are we supposed to fix ur shit when you have the incorrect parts installed. Hit urself in the head!

BobTheBiker · 08-30-2009, 07:09 AM

that was a TOTAL brainfart. I done more than hit myself. I went and drank myself dumb a few hours ago as punishment. who are you again?

101lifts2 · 08-31-2009, 01:31 AM

The master of all automotive.

BobTheBiker · 08-31-2009, 03:49 AM

You cant be the master of all automotive. I know that guy. his name was jesus and he has a beard.

anyways, the fuel issue is sorted, but now when I rev it, its got a nasty rattle from somewhere. I'm inclined to say the belt tensioner because the belt on it is obscenely small and puttin a good deal of strain on the tensioner. plus a portion of my belt actually got shredded today as I watched. glad my fingers werent in the way.

this noise only happens briefly then disappears, and only happens on quick acceleration of the motor's rpms. doesnt sound like a constant rattle from top or bottom end like a bearing going out.

08-28-2009, 10:36 PM	#1
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	96 S10 fuel issue Anyone have some ideas here? I've got a 96 S10 2.2, everyting is wired up right, and hooked up where its supposed to be, but I cant get the truck to run because the fuel injectors arent firing as they need to be. I've got ONE plug I cant figure out, looks just like the cam position sensor plug, but the notch is different and theres nowhere for it to go on my motor. Right now, the truck runs with ether in the intake, but wont start on its own. I'm not really sure WTF to make of it, but its annoying as shit. anyone got some input? My only idea now is ECU is toast.

08-29-2009, 09:43 PM	#4
101lifts2 WSB Champion Join Date: Nov 2008 Location: Anaheim, CA Moto: 2009 Kawi ZX6R Posts: 5,570	How are we supposed to fix ur shit when you have the incorrect parts installed. Hit urself in the head! __________________ Train Hard Ron Paul - 2012 Mark of Excellence GM

08-31-2009, 01:31 AM	#6
101lifts2 WSB Champion Join Date: Nov 2008 Location: Anaheim, CA Moto: 2009 Kawi ZX6R Posts: 5,570	The master of all automotive. __________________ Train Hard Ron Paul - 2012 Mark of Excellence GM

08-29-2009, 02:59 AM	#3
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	I was looking at it more earlier and the issue dawned on me. I had the wrong fucking crank sensor in there. people keep saying how the crank sensor is behind the motor mount, but never mention a wire going to the coil off it, so I had to go swap with the one off my original block, along with the original coils. BAM! problem seems to no longer be a problem, and all but 3 plugs(former AC system and one evap unit) now have homes. I'll test better in the AM since I'm in an apartment complex and theres little kids livin next to where I work on my truck. dont need angry neighbors.

08-30-2009, 07:09 AM	#5
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	that was a TOTAL brainfart. I done more than hit myself. I went and drank myself dumb a few hours ago as punishment. who are you again?

08-31-2009, 03:49 AM	#7
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	You cant be the master of all automotive. I know that guy. his name was jesus and he has a beard. anyways, the fuel issue is sorted, but now when I rev it, its got a nasty rattle from somewhere. I'm inclined to say the belt tensioner because the belt on it is obscenely small and puttin a good deal of strain on the tensioner. plus a portion of my belt actually got shredded today as I watched. glad my fingers werent in the way. this noise only happens briefly then disappears, and only happens on quick acceleration of the motor's rpms. doesnt sound like a constant rattle from top or bottom end like a bearing going out.